FPBX <SIP> Adtran 908 <PRI> Avaya CM

[BigBro]

Hello,

we are trying to configure an ISDN PRI link between Avaya CM and Adtran 908e Gen2. Everything is working fine, except that the callers names are received in the DISPLAY but cannot be forwarded to FPBX. Is there any way for Adtran to send the name from the display part?

I've tried with no luck:

isdn name-delivery display

isdn name-delivery proceeding

isdn name-delivery setup

-----

11:54:25.671 ISDN.L2_FMT PRI 1 M - 05 SETUP
11:54:25.671 ISDN.L2_FMT PRI 1 IE - 04 BEARER CAPABILITY Len=3
11:54:25.671 ISDN.L2_FMT PRI 1 90 Xfer Cap.:3.1 kHz AUDIO
11:54:25.671 ISDN.L2_FMT PRI 1 90 Xfer Rate:64k
11:54:25.671 ISDN.L2_FMT PRI 1 A2 Layer 1:G.711 U-Law
11:54:25.672 ISDN.L2_FMT PRI 1 IE - 18 CHANNEL ID Len=3
11:54:25.672 ISDN.L2_FMT PRI 1 A1 Primary Rate
11:54:25.672 ISDN.L2_FMT PRI 1 Intfc ID:IMPLICIT
11:54:25.672 ISDN.L2_FMT PRI 1 Pref/Excl:PREFERRED
11:54:25.672 ISDN.L2_FMT PRI 1 D-Chan Indicated:NO
11:54:25.672 ISDN.L2_FMT PRI 1 Chan. Sel:FOLLOWS
11:54:25.672 ISDN.L2_FMT PRI 1 83 Numb/Map:NUMBER
11:54:25.672 ISDN.L2_FMT PRI 1 88 Channel:8
11:54:25.672 ISDN.L2_FMT PRI 1 IE - 1E PROGRESS INDICATOR Len=2
11:54:25.673 ISDN.L2_FMT PRI 1 81 Location:LPN
11:54:25.673 ISDN.L2_FMT PRI 1 83 Description:ORIG. NOT ISDN
11:54:25.673 ISDN.L2_FMT PRI 1 IE - 6C CALLING PARTY # Len=6
11:54:25.673 ISDN.L2_FMT PRI 1 21 Numb. Type:NATIONAL
11:54:25.673 ISDN.L2_FMT PRI 1 Numb. Plan:E.164
11:54:25.673 ISDN.L2_FMT PRI 1 80 Presentation:ALLOWED
11:54:25.673 ISDN.L2_FMT PRI 1 Screening:USER PROVIDED
11:54:25.673 ISDN.L2_FMT PRI 1 Ph.# 7710
11:54:25.674 ISDN.L2_FMT PRI 1 IE - 70 CALLED PARTY # Len=5
11:54:25.674 ISDN.L2_FMT PRI 1 A1 Numb. Type:NATIONAL
11:54:25.674 ISDN.L2_FMT PRI 1 Numb. Plan:E.164
11:54:25.674 ISDN.L2_FMT PRI 1 Ph.# 8020
11:54:25.674 ISDN.L2_FMT PRI 1 IE - 96 SHIFT - CODESET 6 Len=0
11:54:25.674 ISDN.L2_FMT PRI 1 IE - 28 DISPLAY Len=15
11:54:25.674 ISDN.L2_FMT PRI 1 (EN) Mr. Test
11:54:25.675 ISDN.CC_MSG PRI 1 CC>>Host: 02 00a4 SETUP_IND
11:54:25.675 ISDN.CC_MSG PRI 1 Host>>CC: 00 00a4 CALL_PROCEEDING_REQ

[BigBro]

I came across this information, but I'm wondering if it is intended specifically for Gen3 devices?

calling-party name-facility-timeout Use the calling-party name-facility-timeout command to set the name facility timeout. This value determines the number of seconds to wait for the calling-party name delivery after the initial SETUP message is received. Once the name delivery is received or the timeout has passed, the corresponding INVITE is sent using the Session Initiation Protocol (SIP) trunk. Set the value to 0 to eliminate the delay. Use the no form of this command to return to the default setting.