cancel
Showing results for 
Show  only  | Search instead for 
Did you mean: 
Anonymous
Not applicable

ERL Tool abnormal termination

Jump to solution

I Have a new installation of a 7100 with an Analog line attached.  When trying to use the ERL tool, I get this message back:

CNL_NV7100_MEX(config-fxo 0/1)#test erl all auto-set

08:12:38 ERL.INFO  fxo 0/1 erl measurement started, using impedance 600cCNL_NV7100_MEX(config-fxo 0/1)#

08:12:41 ERL.INFO  fxo 0/1 impedance 600c - abnormal test termination

2014.06.17 08:12:41 ERL.INFO  fxo 0/1 Did not auto-set impedance because of abnormal test completion

2014.06.17 08:12:41 ERL.INFO  fxo 0/1 erl test terminated abnormally

CNL_NV7100_MEX(config-fxo 0/1)#

I know we are connected because you can call in and hit the line.  However you cannot talk over it due to buzzing and low volume.  A 2500 set was plugged into the circuit and works fine.

Thanks

Labels (1)
0 Kudos
1 Solution

Accepted Solutions
Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

We got it working.  There was a line attached to the port, but there was a DSL that was not properly filtered on it.  Also the ERL would not work until Blind Dialing was enabled on the circuit.

View solution in original post

0 Kudos
14 Replies
jayh
Honored Contributor
Honored Contributor

Re: ERL Tool abnormal termination

Jump to solution

Double-check your wiring.  It sounds like you might have a ground on the line.  If you have a second FXO port, swap them to see if the trouble follows the line or the port.  Bad hardware is a possibility if the 7100 has an internal short to ground.

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

We did swap the line to the second FXO port and i could not run the test on that either.  We tested with an analog phone and hear no ground hum.  There is a DSL, but there is a splitter at the NID provided y the carrier.  Unfortuanly this system is installed in Mexico as a remote office, and can do little testing .  Is there a way to locally loop back the FXO to a local FXS port to verify the hardware? 

jayh
Honored Contributor
Honored Contributor

Re: ERL Tool abnormal termination

Jump to solution

You could probably patch an FXO to FXS for testing, ideally on a second box just as a simulated line. It would be a tricky configuration on one unit.  Do the people on site have a multimeter and can they verify -50 volts and ground on the incoming line when on-hook?  It's possible that it is overvoltage and causing a MOV surge protector in the Adtran unit to fire. 

Just for testing, try rolling tip and ring on the pair and see if that fixes it.  Normally the Adtran gear isn't polarity sensitive but you never know.

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

There is no second box to test off down there. I can inqure about the

multimeter. How would the setup look for testing off the same unit?

Neither of the FXS ports are currently in use, and we can do whatever we

want with them. Does the ERL tool need to actually place successful

calls out to work properly?

Andrew

jayh
Honored Contributor
Honored Contributor

Re: ERL Tool abnormal termination

Jump to solution

I'm not sure exactly what it does, I've never used a 7100.  Ideally, it would call a local central office test number that provides a silent termination, then run a sweep tone and measure what comes back.  As Adtran has no idea where any specific unit will be placed or what test number to use, this isn't going to be practical.  In practical terms, an ERL test shouldn't be required to turn up the interface and place calls.  It would be useful for setting impedance to match local conditions.

If the ERL allows you to specify a destination number, then call a POTS line, answer with a standard 2500 set in a location as quiet as possible.  The goal is to terminate the connection with something closely resembling a standard telephone that produces no signal of its own.  Once terminated, the tester sends a signal.  Ideally 100% of that signal is absorbed by the other end (your 2500 set in a quiet room). Any signal that is reflected back is measured, higher signals are worse.  "Loss" is considered a bad thing generally, but in the case of "Echo Return Loss", the more loss (less reflected signal) the better.

The concept is similar to SWR on a radio circuit.  

The ERL test and hybrid balance is going to be very subtle if noticeable at all to the person on the 7100.  If out of whack it may be noticeable to the remote party as echo.  It can also affect modem and fax transmission.

In your case, if you have clearly audible hum and low volume there is something else going on with the physical loop or interface.

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

Andrew,

When activated the ERL tool goes off hook, verifies loop current and dial tone (unless blind-dial is enabled), then generates white noise with a particular impedance value set, and measures the resulting echo level.   When using the command test erl all auto-set, this process will be repeated with all the different impedance values.  The value that results in the best ERL (highest value) will be configured on the trunk.  This test cannot complete when calls are coming into or going out of the FXO interface, so it needs to be performed at a time when traffic is minimal.  You can read more about the ERL Tool in this document:

I agree with jayh that this sounds like a line issue.  Were you able to resolve it?  If so can you come back to this thread to provide an update so others can benefit from the information?

Thanks,
Matt

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

We may be replacing this trunk with a SIP trunk, might not be an issue.

Plugging in a 2500 set produces no call quality issues on this line,

only when plugged into the 7100. Can I test the FXO interface by

looping back from an FXS?

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

Andrew,

To answer your question I would not recommend plugging an FXS into a FXO of the same unit as a reliable way to test. Were you ever able to get the bottom of this issue?  Was it the line?

Thanks,

Matt

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

No resolution. I think they abandoned the use of the local circuit. We

are routing all calls through a SIP trunk to the main 7100. Are there

any tools available to see why we get "abnormal termination" of the ERL

tool?

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

The gives some possible causes for this:


During test execution, a warning is issued if a test sequence terminates abnormally. Reasons for early


termination include:


• The line cannot be seized.


• The line disconnects during test.


• DSP times out (for example, when the DSP hardware version does not support the automated method).


• The test runs for more than 20 seconds per impedance value (for example, 80 seconds with an


impedance setting of 4).


While running the test the it may be helpful to also enable debug voice erltool and debug interface fxo.

Thanks,

Matt

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

This is what i get when i enable the interface and run ERL. I am

guessing there is a line issue. This site is not near me to physically

examine.

16:07:00.662 FXO.0/1 Hook Switch Open

16:07:00.662 FXO.0/1 Hook Switch Open

16:07:00.662 FXO.0/1 FxoPortStateOnhookReverse -> FxoPortStateInit

16:07:00.662 FXO.0/1 FxoPortStateInit: onhook() in base state

16:07:00.662 FXO.0/1 Hook Switch Open

16:07:00.663 FXO.0/1 FxoPortStateInit: onhook() in base state

16:07:00.665 FXO.0/1 Ringing

Debounce:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::*:::::::::::ÿ

16:07:00.665 FXO.0/1 Tip Ground

Debounce::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::*::::::::::ÿ

16:07:00.665 FXO.0/1 FxoPortStateInit -> FxoPortStateOnhook

2014.09.16 16:07:00 INTERFACE_STATUS.fxo 0/1 changed state to up

16:07:00.730 FXO.0/1 FxoPortStateOnhook -> FxoPortStateOnhookReverse

CNL_NV7100_MEX(config-fxo 0/1)#test erl all auto

16:07:57 ERL.SM fxo 0/1 Port setup saved: tx +0.0 dB, rx +0.0 dB,

impedance 600c

16:07:57 ERL.SM fxo 0/1 Created loopback account erltoolLbA

16:07:57 ERL.SM fxo 0/1 ErlToolIdleState -> ErlToolPredeliverState

16:07:57.901 FXO.0/1 Hook Switch CCNL_NV7100_MEX(config-fxo 0/1)#losed

16:07:57.901 FXO.0/1 offhook

16:07:57.902 FXO.0/1 FxoPortStateOnhookReverse -> FxoPortStateOffhook

16:07:57 ERL.INFO fxo 0/1 erl measurement started, using impedance 600c

16:07:57 ERL.SM fxo 0/1 ErlToolPredeliverState -> ErlToolSeizingState

16:07:58.132 FXO.0/1 loop feed open

16:07:58.132 FXO.0/1 FxoPortStateOffhook -> FxoPortStateLoopfeedOpen

16:07:58.632 FXO.0/1 Hook Switch Open

16:07:58.632 FXO.0/1 onhook

16:07:58.632 FXO.0/1 FxoPortStateOnhookPending -> FxoPortStateOnhook

16:07:58.632 FXO.0/1 FxoPortStateOnhookPending -> FxoPortStateOnhook

16:07:58 ERL.SM fxo 0/1 ErlToolSeizingState ->

ErlToolClearingCompleteState

16:07:58.690 FXO.0/1 FxoPortStateOnhook -> FxoPortStateOnhookReverse

16:08:00.134 FXO.0/1 Hook Switch Open

16:08:00.134 FXO.0/1 FxoPortStateOnhookReverse::onhook()

16:08:00 ERL.SM fxo 0/1 ErlToolClearingCompleteState -> ErlToolIdleState

16:08:00 ERL.INFO fxo 0/1 impedance 600c - abnormal test termination

16:08:00 ERL.SM fxo 0/1 Port setup restored tx +0.0 dB, rx +0.0 dB,

impedance 600c

2014.09.16 16:08:00 ERL.INFO fxo 0/1 Did not auto-set impedance because

of abnormal test completion

2014.09.16 16:08:00 ERL.INFO fxo 0/1 erl test terminated abnormally

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

That output looks similar to what you get when there is nothing plugged in.  Can you reply with the output from a show run  int fxo 0/1 verbose and show int fxo 0/1?

Thanks,
Matt

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

!

interface fxo 0/1

description ""

alias

impedance 600c

rx-gain +0.0

tx-gain +0.0

no shutdown

!

end

CNL_NV7100_MEX#sho int fxo 0/1

fxo 0/1 is UP

Two-wire Status: Onhook

Test Status: INACTIVE

No Tests

Impedance: 600 ohms +2.16uF

Transmit Gain: +0.0dB

Receive Gain: +0.0dB

Measured ERL: not available

Last clearing of "show interface" counters: never

Anonymous
Not applicable

Re: ERL Tool abnormal termination

Jump to solution

We got it working.  There was a line attached to the port, but there was a DSL that was not properly filtered on it.  Also the ERL would not work until Blind Dialing was enabled on the circuit.

0 Kudos